How to Pull Honda Codes without a Scanner: Code Diagnostic

If you are short of cash, you no longer need to hire a professional mechanic to scrutinize the problem affecting your car.

But first, do you know how to pull Honda codes without a scanner? Troubleshooting Honda codes via manual means isn’t a cumbersome process if you own a car that uses the OBD1 or OBD 2.

If your car’s dashboard flashlight starts to appear, then there is something not right.

Today’s car manufacturers provide an easy way for accessing troublesome codes. Like most car technicians, you can pull the Honda car codes without having a scanner.

In this review post, we will go through the process of pulling out these codes.

Accomplishing this task isn’t that hard and is a process that is as easy as A-B-C-D. Sometimes, we know it can be tricky to be armed with current auto-scanners, which are fast at troubleshooting vehicles’ codes.

Without further delay, let’s get started by describing the process of pulling Honda car make without a scanner.

How to Pull Honda Codes without a Scanner

Pulling the Honda codes via manual means is a super simple and fast process.

A necessary tool you ought to have is a metal wire. Essentially, this thin metal wire should have a metal clipper. Also, a booby pin can be used along with the wire and this tool should lack the pointing part.

Also, the pointed part ought to be made of metal since it will get into contact with the diagnostic mechanism or system. Beneficially, this part helps to ensure the diagnostic mechanism is auto.

Method 1: The Manual Method

Let’s now look at how you can pull the Honda car make codes by the manual method:

Step 1

Start by effectively turning off your Honda car.

Step 2

Proceed to ajar the metallic clippers until they form a U shape.

Step 3

Locate the diagnostic system in the Honda car. Usually, this car component is located underside part of the glove on the left or right side.

Step 4

Embark to open this vehicle part and locate the connector installed on the diagnostic system. In most scenarios, there are two, with one having 3 cavities that help to connect the scanner.

Lastly, the other has 2 cavities for installing the metal wire. Also, it helps to harness the auto-mode of the diagnosis system.

Step 5

Proceed to install each end of the thin metal wire or the said bobby pin on each side of the 2 cavity connectors.

Step 6

After that, proceed to turn the Honda car and ensure the ignition mode is on. Don’t turn on the Honda car engine.

Step 7

Scrutinize and check on the dashboard if the CEL flashes. If this part has a flashlight, then there is a potential malfunction on the Honda car.

Step 8

To effectively read the codes, check for the length of the flashes depicted on the dashboard. A much longer code means that the malfunction has reached numbers 10.

In case you see shorter codes, then the malfunction quantity is 9 and below. Not to forget, each code is taken when a pause happens.

Step 9

By now, you should have read the CEL codes and proceed to install the connectors on the designated compartment part. Ensure that it’s effectively connected for the longer thriving of the connectors.

Method 2: Using Scanner Tools [How to Pull Honda Codes without a Scanner]

As we have seen, reading Honda codes via manual means is a simple process. Following all the steps mentioned above will help you pull Honda codes without utilizing a scanner tool thoroughly.

Let’s now look at the other method of pulling Honda codes……

To pull codes for the Honda car, an ignition tool can be used. All that is required is to turn the ignition key off and on and don’t crank the Honda engine.

Depending on the make of your car, this process can be repeated severally.

For most cars we have encountered, this process needs to be repeated five times. Other vehicles require this process to be repeated 3 times.

All that matters is the model of the Honda car you want to pull without scanning. To accomplish this vital task, leave the ignition key on. In case the Honda engine is turned on by mistake, start this process all over again.

After making the turns, the Honda service light should be illuminated. Importantly, check for the specific no. which is showed by every single pulse of light appearing on the vehicle dashboard.

A 2 digit code indicates a separation of one digit proceeding to the next. However, the Honda troubleshooting codes appear in this design, and the separation of each shows a different malfunction meaning.

Since you can find the meaning of different codes on the user repair guide.

Method 3: Utilizing the Odometer [How to Pull Honda Codes without a Scanner]

To retrieve the Honda codes, you can utilize an odometer.

To start, depress the odometer of the car and ensure the reset and trip buttons are reset. Proceed to turn off and on the ignition key.

Next, the said buttons of the odometer should be released. Honda codes will then appear on the screen of the odometer.

As we said earlier, pulling Honda codes without using a scanner is not a complex process.

Follow these three methods and you will be able to detect codes and repair this monster car effectively.

Never should it be cumbersome to detect flaws affecting the Honda car make if you have this info by your finger point.

Honda Trouble Codes List

Like other automotive makes, Honda cars can flaw and it’s vital to troubleshoot them to locate the real problem.

In this section of how to pull the Honda codes without a scanner review, we are going to detail and elaborate on some common trouble codes.

01. 02A Trouble Code

An error code that shows malfunctioning of the rear oxygen sensor. In case there is low or high voltage, the O2 sensor fails to read the right amount of oxygen found in the exhaust.

As a result, this leads to a malfunction or complete failure.

02. 02B Trouble Code

An error code that varies in terms of the voltage supplied to the oxygen amount in the car exhaust. Varies from 0.1 – 0.9 voltage.

For 0.1 V, there is low exhaust, while 0.9 V indicates excess exhaust.

All in all, this trouble code affecting the O2 sensor component depicts low or extreme or has become inactive.

03. MAP Trouble Code

Depicts a problem affecting the MAP sensor with extreme voltage input directed to the ECU.

Extreme voltage is a commonly experienced flaw that prevents proper engine operation in terms of operating the MAF and TPS.

04. CKP Trouble Code

An error code is harnessed when the PCM cannot detect the right sensor functioning around the crankshaft sensor.

A car with this type of code will display CEL on the dashboard area, making a failsafe mode to be enabled.

05. P0107 MAP Trouble Code

A Honda trouble code that shows the sensors have low voltage input to the ECU. Encountering this code means that the overall input voltage is around 0.5 or much lesser.

For proper Honda engine operation, this voltage is way too low.

06. P0116 Trouble Code

A flaw code indicating the engine control module is read by ECT. Also, it shows the range of performance doesn’t meet the overall ECM required for engine cold and warm start.

All this happens before the next cold starts.

07. P0123 Trouble Code

A generic trouble code that shows the ECM has noticed the TPS circuit. In this case, the output voltage surpasses the expected sensor’s voltage.

Also, it indicates there is a short in wiring or sensor.

Notable diagnosis symptoms include; higher idling of car engine than normal and lack of car’s to be driven at slow speed with less throttle responsiveness.

08. TDC Trouble Code

A fault in the TDC sensor will trigger this code and in most cases, the vehicle will go in the limp mode or make the Honda engine light come on.

A notable cause for this flaw is the damage of TDC resulting from the distributor bearing or an open circuit around the sensor area.

09. CYP Trouble Code

A problematic code that shows the CYP is damaged.

Damage to the CYP occurs when it’s damaged from the wiring area or the open circuit. A notable symptom is grinding metallic noises and this calls for the tool replacement.

10. P0110 Trouble Code

It is associated with the malfunctioning of the air temperature sensory circuit.

The presence of this error code means that the IAT circuit is sending the wrong voltage. All this causes the ECU to manage inefficient fuel utilization.

FAQs About Honda Codes

Frequently Asked Questions part of this review is rich with some notable online queries that most people ask about pulling Honda codes without a scanner.

Here are some commonly asked online questions concerning the accomplishment of this vital task.

Q: Is it possible to troubleshoot Honda codes on my own?

Ans: Yes. By having the above-mentioned tips, it’s supper possible to achieve this process solely.

Being able to pull Honda codes solely helps avoid huge costs associated with hiring a professional mechanic.

Q: What are codes?

Ans: Codes usually show potential damages in the gearbox, ignition, engine, and exhaust emission system.

Usually, Honda car makes have two types of codes and they include the Honda CEL and Honda trouble codes list.

Q: Do codes differ in terms of different car models?

Ans: Yes. Codes usually differ from one model of Honda car to the other.

Also, it’s paramount to recognize codes differ after some time. Ensure that an updated list is available when checking the meaning of each code.

Q: What are the first signs of Honda malfunction?

Ans: In case the Honda car has malfunctioned, the first place to be alerted is the OBD. To show potential signs of malfunction, the Check Engine Light turns on.

You can locate this by checking the car dashboard area and check for a bright light color.

Q: What are some potential risks associated with not interpreting the CEL codes properly?

Ans: Although as a driver or car owner, you have the best intentions to ensure you read codes, sometimes it becomes difficult to read them.

If you fail to read codes thoroughly, the risk is much less than when you ignore them.

Failure to correctly read codes will lead to excess malfunction of different parts of the Honda car make.

Q: What if I can pull the Honda codes without using a scanner?

Ans: If you are having difficulties pulling Honda codes without a scanner, then it becomes crucial for the car owner to consult a professional garage.

Although he or she will charge you some monetary fee, these people know better how to pull the Honda codes and are thus helpful.

Verdict

As we have seen, it’s possible to pull the Honda codes without utilizing a scanner. To achieve this task, you can utilize any of the three methods we have described in this post.

To get Honda error codes is a wise venture that ensures your most prized asset functions at the best levels. Also, it helps car users and drivers avoid flaws associated with sudden engine failures.

We always care for car owners and that’s why we provide content-rich in true and validated info on how to handle vehicles better.

As such, following all info provided in this blog review post will never leave one in a ditch. As a recommendation, Honda cars need to follow the manufacturer’s instructions when it comes to reading error codes.

In case you find any valid info we might have omitted accidentally in drafting this piece, include the info in the review section.

We hope you now know how to pull Honda codes without a scanner. Most importantly, this make of car is one of the best and deserves the greatest maintenance.

Continue following us and we will reward you with great reviews always.

Leave a Comment